The article author is making a few good pointers relating to How to Install a Bathtub in general in this post in the next paragraphs.
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably challenging job. If the old bathtub is easily obtainable, the task can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Ensure you have actually certified yourself for the work and also are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed project, it is far better to consider using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you mount a new bath tub in your bathroom if you have actually currently purchased a brand-new bathtub as well as do not need to alter the setup of your previous water supply pipes.
Your devices and also product checklist ought to make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be fairly bothersome because of the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the tap in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the called for setting. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Turn on the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and likewise check the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the tub should wait up until the bathtub has actually been used a minimum of once as this will resolve it right into its final setting.
Preparing for the Setup
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, bring about difficulties with dampness and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in usage. The sealer can break fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub? Place a remark directly below. We would be pleased to find out your opinions about this entry. In hopes to see you back again before long. If you liked our blog posting plz remember to share it. Thank-you for your time invested reading it.
Act immediately.